LIFT ACCESSORIES
Installing A-PLY®
Smooth Faced Walls
Navy Walls
A-PLY - In The Field®
Services
Custom Installations
Extreme Conditions
Contact A-PLY®
E-Mail A-PLY®
For Further Info
On A-PLY®
Permitting
Permitting Info
Boat Lifts
All About Boat Lifts
Hi-Tide Boat Lifts
Lift & Dock Accessories
Hi-Tide Boat Lift Video
Lift Contact Info
E-Mail Us
For Further Info on Boat Lifts
Consulting
About Us
Consulting Services
Expert Witnessing
Training Books
On-Site Training
What's New
Request for Information/Contact
External Links
Hi-Tide Boat Lifts
ACE Inc. is the exclusive distributor in the New York area for Hi-Tide engineered and time tested Boat Lifts. Hi-Tide, inventor of the first all aluminum boatlift was founded in 1979. Hi-Tide is the industry leader and innovator producing lifts from 650 to 180,000 pounds. The lift and accessory line is the most extensive and available in the industry today!
WIRELESS REMOTE CONTROL
This unit allows for the remote operation on one, two, four or more motor, boat lifts from the land or on board the vessel AND also controls dock lights or electrical accessories at the waterfront.
LIMIT SWITCHES
These control the extent of lift travel up and/or down. This eliminates the chance of cable fowling or breaking.
BOARDING PLATFORM
A safe and secure, flip-up boarding option for floating or fixed docks, piers and seawalls.
Boarding Platform with Hand Rail.
SERVICE PLATFORMS
A convenient way to work on stern drives, transoms and lower outboard units from the boatlift. It attaches to the rear or stern lifter beam.
ALUMINUM CATWALK
Provides a convenient way for the boat owner or service person to clean, wax or service the sides and bottom of a vessel. It also allows an operator to install shrink-wrapping around the vessel for the winter.
ANGLED LIFTER BEAMS
This option is used when the water, next to a bulkhead or seawall, is too shallow to use conventional, straight lifter beams.
3-STEPS FOR CATWALK
When mounted to a catwalk these all aluminum steps (2 step also available) allow the boater to board the vessel from along side the hull.
DRIVE SHAFT COVERS
These covers, in a LOW PROFILE installation, are installed over the top rail beams. They also provide a stepping surface for the boater.
CUSTOM BUNKING |
BUNK RISER BRACKETS |
CHOCK BRACKETS |
FLAT BUNKS |
ALUMINUM BUNKS These options are for the boater who, in most cases does not want wood in contact with the hull bottom. These bunks also replace wood that is not allowed to be used in certain waterways of particular counties in the U.S. |
|
PIVOTING V-BLOCKS
These options are also used when the boat owner has a deep “V” hull, a trawler type hull, steps in the hull bottom, a hull with a keel or other configuration that does not allow the use of conventional straight carpeted bunks.
MARINA BRACKETS
These optional brackets allow (2) top rail boatlift supports to be mounted on the same pair of piles. This installation is usually found in a commercial marina or when a customer wants to save space and the cost of extra piles.
SNAP-IN TRANSPARANT COVERS FOR ALUMINUM LIFTS
These hi-impact smoke colored formed Lexan® covers protect the cable and winders and add beauty to the lift top.
ROOF BRACKETS
These provide a simple structure to attach a rigid or canvas roof over a boatlift. The roof keeps rain, sun, snow and ice and other debris off the boat.
FLARE GUIDE
This device automatically self-centers the boat or yacht hull on the bunk supports. Ideal for lifts that operate in rough waters and high winds. The device is also used to brace and support the guide poles (in the boat bow too!!) on any aluminum boatlift.
DAVITS
These davits are available from 650 to 6,500 lbs. each
Davits available with Gear Drive® winch option.
LADDERS
|
DOCK LADDERS Fixed, Slide, Flip-up |
 |
FINGER PIER LADDERS Fixed, Slide |
 |
FLOATING DOCK LADDER
Featuring Slide Action AVAILABLE ONLY WITH 3 NON-SKID STEPS |
